Restaurant Small Size Buzzer Electronic Slim Coaster Pager
| Host |
Pager |
| Input Power |
DC12V/2A |
Battery |
Li-ion 3.7V 300mAh |
| Frequency |
433.92MHz |
Frequency |
433.92MHz |
| Transmit Power |
26dBm |
Standby Current |
<12mA |
| Standby Power |
<120mW |
Standby Duration |
10h |
| Modulation Type |
FSK |
Sensitivity |
-115dBm |
| Max Capacity |
998 pagers |
Max Distance |
800m-1000m |
| Backup Battery |
Li-ion 3.7v 1000mAh |
Prompt Mode |
Vibration/Buzzer/Flashing |
| Dimensions |
110*165*50mm |
Prompt Time |
30s |
| Output |
DC5V/4A |
Input |
Type-C DC5V/2A;
or DC12V/2A |
Instructions for Use
A. Before usingWiring: Host connects to power source via adapter. Charging base connects to host via Type-C cable.
Connect host to power source, and charge pagers for 10 minutes at least before using.
Charging Indicator Information:
| Host |
Pager |
| Red LED |
Charging |
Flashing |
Charging |
| Green LED |
Full Charged |
Always On |
Full Charged |
B. Operating InstructionCALL mode is the default mode. Continuously press Delete button (←) to return Call Mode while in other mode. C--- is displayed in CALL mode.
Input the number and press CALL button to call the corresponding pager.
C.Mute modePress MUTE and 999 (S999 displayed) then press CALL, all charging pagers change to MUTE mode.
Press MUTE and 000 (S000 displayed) then press CALL, all charging pagers change to normal mode.
In MUTE mode, all pagers only vibrate and flash while being called.
Continuously press DELETE button (←) to return CALL mode. (C--- displayed)
D.Call HistoryPress button
H to check the recent 10 called numbers (HXXX displayed). Press
△/▽ button to page up/down.
Continuously press DELETE button (←) to return CALL mode. (C--- displayed)
Note: No looping of △/▽.
E. One-Call-OffIn
CALL mode, press 999 and
CALL, all charging pagers will be off. Re-charge pagers will turn on again.
Note: This instruction is invalid to the pagers not being charged.
F. Host OffWhen powered by battery, long press H and △ at same time, host is off. Long press H and ▽, host is on. This operation is invalid when powered by power source.
G. Program OperationAll pagers are programmed before delivery. So this operation is only necessary when adding new pagers or changing numbers.
Put the pagers on the charging base, press P and 999 (P999 displayed), then press CALL to enter programming mode. The operation must be finished in 20 seconds after pagers are charged.
In programming mode, all LED display of the pagers will keep flashing.
Then input number and press CALL, all pagers display this number. Move the top pager away, the pager will beep once and stop flashing. It means the pager is programmed.
Repeat the steps to program other pagers.
Note:
The pagers will quit programming mode if no operation within 1 minute. All pagers' numbers will not change if not being programmed.
1 pager only can be programmed 1 number. Old number will be replaced by the new one.
Instruction Description
| Instruction |
Buttons |
Display |
Function |
| Programming Mode |
P 999 CALL |
P999 |
To enter programming mode |
| History |
H |
H + Number |
Check recent 10 call records. |
| Mute Mode |
999 Call |
S999 |
All charging pagers switch to MUTE mode. |
| Quit Mute Mode |
000 Call |
S000 |
All charging pagers quit MUTE mode. |
| Call pagers |
[Number] Call |
C+[Number] |
The corresponding pager begin to remind. |
Common Troubles and Solutions
| Trouble |
Analysis |
Solution |
| The pager can't be programmed. |
1.The pager is not being charged.
2.Charging is more than 20s. |
1. Make sure the pagers are well charged.
2. Try again within 20s after recharging. |
| The pager can't be One-Call-Off |
The pager is not being charged. |
Make sure the pagers are well charged and try again. |
| The pager doesn't response. |
1. The pager is out of power.
2. Out of call range. |
1.Use after full charged.
2.Use within range of call. |
Audited Supplier 
Audited Supplier 
){kind=link}
){kind=link}